How reconstitution math works

Three divisions take you from a vial label to a mark on a syringe.

Every peptide calculator, including the ones on this site, does the same three pieces of arithmetic. Once you can do them by hand, you can check any result in a few seconds, and you will notice when a number looks wrong.

What you need before you start

Three numbers, each with its unit:

  • The amount in the vial. Printed on the label, usually in mg, sometimes in mcg or IU.
  • The liquid added. In mL. This is the volume the powder is dissolved in.
  • The dose. As written in your instructions, in mcg, mg or IU.

And one fact about your syringe: its scale. Most insulin syringes are U-100, meaning 100 units fill 1 mL.

Step 1: concentration

Concentration is how much compound is in each mL of liquid. Divide the amount in the vial by the liquid added.

concentration = amount in vial ÷ mL of liquid

A 5 mg vial with 2 mL is 5 ÷ 2 = 2.5 mg per mL. Because 1 mg is 1,000 mcg, that is also 2,500 mcg per mL. Write down both if your dose is in mcg; it saves a conversion later.

Step 2: volume

Now divide the dose by the concentration. The units of weight must match: mcg with mcg per mL, or mg with mg per mL.

volume (mL) = dose ÷ concentration

A dose written as 250 mcg from that vial is 250 ÷ 2,500 = 0.1 mL. If the dose were written as 0.25 mg, you would get 0.25 ÷ 2.5 = 0.1 mL, the same answer, because it is the same amount.

Step 3: syringe units

Multiply the volume by your syringe scale.

units = volume (mL) × 100 on a U-100 syringe

0.1 mL × 100 = 10 units. On a U-50 syringe you would multiply by 50 instead (5 units), and on U-40 by 40 (4 units). The volume is the same; only the printed number changes.

A second example, in mg

A 10 mg vial mixed with 2 mL, and a dose written as 1.25 mg:

  1. 10 mg ÷ 2 mL = 5 mg per mL.
  2. 1.25 mg ÷ 5 mg per mL = 0.25 mL.
  3. 0.25 mL × 100 = 25 units on a U-100 syringe.

These numbers only demonstrate the arithmetic; they are not a suggested dose.

Doses per vial

Divide the amount in the vial by the dose, in the same unit. 10 mg ÷ 1.25 mg = 8 doses. Notice that the water does not appear in this sum. Adding more or less liquid changes how much volume each dose takes, never how many doses the vial holds. In practice a little liquid stays in the vial and the needle, so you may get slightly fewer full draws than the arithmetic says.

Going backwards: water for a target

Sometimes you want each dose to be a convenient number of units. Rearrange the same three steps:

  1. Turn the target units into mL: 10 units ÷ 100 = 0.1 mL.
  2. Find the concentration that puts one dose in that volume: 250 mcg ÷ 0.1 mL = 2,500 mcg per mL.
  3. Find the liquid that gives that concentration: 5,000 mcg ÷ 2,500 mcg per mL = 2 mL.

The reconstitution calculator does this and rounds the water to something you can measure. How much liquid to use, and which liquid, should come from your product or pharmacy instructions; the arithmetic only tells you what follows from a choice.

Checks that catch mistakes

  • Is the answer a thousand times off? You probably mixed mg and mcg. Convert one of them and redo step 2.
  • Is the draw more than the syringe holds? Re-read the dose and the vial label. If both are right, the numbers simply need a larger syringe or a different set-up.
  • Is the draw under 1 unit? That is 0.01 mL, too small to measure reliably on an insulin syringe.
  • Did you use the scale on your syringe? A units number from a U-100 calculation does not apply to a U-40 syringe.

The calculators show these three steps with your own numbers under every result, so you can compare them with a hand calculation line by line. For the units themselves, see mg, mcg, mL and units explained.

Arithmetic only. This is educational arithmetic, not medical advice. Check every number against your vial label and your clinician's or pharmacy's instructions.

Try the numbers

More guides

Reminders for every dose, on iPhone

Get Kept